 |
 |
 |
| ART. 101
Base with cabinet and chip-collection pan |
ART. 101/A
Rear guard neon light and main isolating switch |
ART. 101/B “Lexan” polycarbonate chip screen with outlined in aluminum, piston to gas and microswitch of emergency |
 |
 |
|
| ART. 102
Milling square complete with steel vice |
ART. 103*
Ø 200 chuck with slots |
|
 |
 |
 |
| ART. 103A*
Ø 150 faceplate
with 4 independent jaws |
ART. 104*
Lathe carrier |
ART. 105
Steady rest with three adjustable pins |
 |
 |
 |
| ART. 106
Extra carriage for repeat jobs |
ART. 107*
Ø 100 3+3 high precision self-centering chuck |
ART. 107A*
Ø 100 4+4 high precision self-centering chuck |
 |
 |
 |
| ART. 107B
Ø 125 3+3 high precision self-centering chuck |
ART. 107C
Ø 125 4+4 high precision self-centering chuck |
ART. 108
Adjustable turret with 2 tool posts |
 |
 |
 |
| ART. 109
Tool post for flat turret |
ART. 109A
Tool post for turret with Vee |
ART. 109B
Tool post for turret with morse 1 taper |
 |
 |
 |
| ART. 110 Articulated lamp | ART. 111 6 position star clamp | ART. 112*
Set of 5 mill collets with chuck shaft thread-cover and tie-rod |
 |
 |
 |
| ART. 113
Tap and die support device complete with morse 2 taper collet |
ART. 114*
Fixed dead center morse 3 taper |
ART. 115
Live center morse 2 taper |
 |
 |
 |
| ART. 115A
Live center morse 2 taper for tracing |
ART. 116
Live center morse 2 taper gap |
ART. 116A
Live center morse 2 taper for pipe |
 |
 |
 |
| ART. 117 Cooling unit | ART. 118
0-8 self-clamping chuck for morse 1 109B |
ART. 118A
0-10 self-clamping chuck for morse 2 taper center |
 |
 |
|
| ART. 119 Set of 3 dogs | ART. 120 Set of 3 center noses |
|
 |
 |
 |
| ART. 122
Set of 4 hard metal
tools |
ART. 123
Set of 2 hard metal threading tools |
ART. 124*
Flange for Ø 100 self-centering chuck |
 |
 |
 |
| ART. 125*
Flange for Ø 125 self-centering chuck |
ART. 125A
Flange for Ø 125 self-centering chuck Ø 30 bar passage
|
ART. 126
Set of 3 mild steel jaws for Ø 100 chuck |
 |
 |
 |
| ART. 127*
Lead screw inverter for DAVID 203 |
ART. 128*
Wrench disassembly of chuck ART. 128A For Ø 30 bar passage |
ART. 129*
Wrench for adjusting
bearings ART. 129A For Ø 30 bar passage
|
 |
 |
|
| ART. 130
6 mechanically fixed tools, complete with inserts and keys |
ART. 131
Additional handweel,
lead screw with nonius
|
|
| * Fitted on standard shaft only (Ø 20) | ||